QCS ROBOT TOOLING SYSTEM QUICK CHANGE SYSTEM QCS provides a cost-effective method to increase productivity by virtually eliminating end-of-arm tool change-over time. With QCS, a robot can be re-tooled for a different part and back in service within a few minutes. Compressed air and vacuum lines are automatically connected as the tool plate mates with the clamp base on the robot arm. The clamp handle can be indexed to a convenient position in 30-degree increments. 0.61 [15.5] SIDE A 2.44 [62] 0.49 [12.4] 0.49 [12.4] SIDE B 1.41 [35.8] 0.55 [14] 0.49 [12.4] 2.57 [65.3] 6.11 [155] M5 x 0.8 (10-32 UNF) 4 PLACES O-RING SEALS 8 PLACES G1/8 NPSF 2 PLACES ROBOT CLAMP BASE 0.35 [8.9] 4.2 1 [10 7] Weight: lb. (g) 1.41 (638) 5 3.9 0] [10 HOW TO ORDER OPTIONS QCS-100B- A A = Handle on Side "A" B = Handle on Side "B" C = Custom Mounting* *Submit worksheet from page 17:5 or drawing with order. ©2008 EDCO USA. www.edcousa.net 17:3 0.97 [24.6] TOOLING QCS ROBOT TOOLING SYSTEM 3.4 6 0.2 [5.1] 3.7 [94 ] TOOL PLATE [87 .9] 0.25 [6.4] HOW TO ORDER OPTIONS QCS-100TWeight: lb. (g) 0.85 (383) C (BLANK) = As Pictured C = Custom Mounting* *Submit worksheet from page 17:5 or drawing with order. 6 3.4 .9] [87 2. [62 46 .5] TOOL PLATE HOW TO ORDER OPTIONS 6 2.4 .5] 2 [6 3.4 6 QCS-100TD[87 .9] Weight: lb. (g) 0.77 (347) C (BLANK) = As Pictured C = Custom Mounting TOOL PARK HOW TO ORDER QCS-100P 4.04 [103 ] 0.21 [5.3] TOOLING ©2008 EDCO USA. www.edcousa.net 75 ] 2. 9.9 [6 0.46 [11.7] 4.45 [113 ] Weight: lb. (g) 0.39 (178) 45 3. 6] 7. [8 An optional Tool Park provides convenient storage and protection for end-of-arm tools when not in service. One Tool Park per Tool Plate is required for efficient operation. 17:4 QCS ROBOT TOOLING SYSTEM QUICK CHANGE SYSTEM QCS provides a cost-effective method to increase productivity by virtually eliminating end-of-arm tool change-over time. With QCS, a robot can be re-tooled for a different part and back in service within a few minutes. Compressed air and vacuum lines are automatically connected as the tool plate mates with the clamp base on the robot arm. The clamp handle can be indexed to a convenient position in 30-degree increments. SIDE 0.75 [19.1] A 5.25 [133] 0.75 [19.1] SIDE 0.61 [15.5] B 1.41 [35.8] 0.75 [19.1] 5.25 [133] 8.81 [224] 0.75 [19.1] TOOL PLATE HOW TO ORDER QCS-140T C = Custom Mounting* *Submit worksheet from page 17:5 or drawing with order. 0.25 [6.4] 4.7 [11 9] 6.1 8 [15 7] OPTION Weight: lb. (g) 1.91 (866) G1/8 NPSF 8 PLACES G1/8 NPSF 8 PLACES O-RING SEALS 8 PLACES HOW TO ORDER QCS-140 A = Handle on Side A B = Handle on Side B C = Custom Mounting* *Submit worksheet from page 17:5 or drawing with order. 0.97 [24.6] 0.35 [8.9] OPTION 6.9 3 Weight: lb. (g) 2.58 (1169) [17 6] 5 4.9 6] [12 17:6 ©2008 EDCO USA. www.edcousa.net TOOLING ROBOT CLAMP BASE